TradeStation Help

Momentum Bar Chart

Momentum bars are charted as standard vertical bars with opens, highs lows and closes, yet each bar has a specified price range, rather than being charted in units of time or ticks. With a focus on price movement, long periods of consolidation may be condensed into just a few bars, removing excess noise in the market and highlighting "real" price movements. So it is possible that an entire month of daily bars could fit into a single Momentum Bar, and the next month would have 30 Momentum Bars.

Momentum Bars are built by the underlying closing data that shows the directional trends as per the range amount. Momentum Bar charts are time independent so that time axis increments will not be fixed. The size of the bars will always be the range size set by you and will never be anything smaller or larger unless it is the current bar that is building.

Momentum Bars look like standard bars, but are different in several ways:

 This is the primary difference between Momentum Bar and Range Bar charts.

In this example, the Momentum Bar chart is using a price Range of .1 :  

 

How a Momentum Bar is Built

Since Momentum Bars are driven by price movement, a new Momentum Bar is only created once the specified Range has been exceeded. For example, if the specified Range amount is $10, it means that each Momentum Bar will have a range (High to Low) of $10. It is thus conceivable that a single Momentum Bar could represent several days if the movement throughout those days was only within a $10 price range. Once a Momentum Bar is closed-out, the open of the next Momentum Bar will always be one tick above or below the close of the prior Momentum Bar.

There are no gaps displayed on Momentum Bar charts, so when there is a price gap in the underlying data, "virtual bars" will be inserted as necessary to fill in the gap on the Momentum Bar chart. These "virtual bars" can be easily distinguished from "real" Momentum Bars by their Up Volume and Down Volume values, which will both be zero.  Note, in order for a bar to be considered a "virtual bar", there should be no real price activity contained within the bar.

Momentum Bar Interval Settings

The Range amount determines the size of the Momentum Bars on the chart. One should take careful consideration in the selection of the Range amount. As a rule, the specified Range amount should be greater than the normal oscillation of the underlying data. Selecting a Range amount that is too small will result in the creation of more bars in real-time than will be created when the chart is built historically.  

Suppose that within a given five minute period prices oscillate between 10 and 12, going from 10 to 12, then back to 10 and then back to 12. If the Range amount for this chart were set to 1, in real-time this would result in four Momentum Bars, as shown in the example below:

Since all of the aforementioned oscillations occurred within a five minute period (the specified underlying interval in this example) when the Momentum Bar chart is built historically, that five minute period would be represented by only two Momentum Bars, as shown in the example below:

Only two bars would be displayed, since information about the bar oscillations within that five minute period would be unavailable when building the chart historically.

It is important that the Range amount be greater than the minimum move of the underlying symbol, and it should also be evenly divisible by the minimum move or rounding errors may occur.

The Interval setting specifies the interval of the data used to build the Momentum Bars. The appropriate interval depends on your market perspective. Users with a short-term perspective may benefit from using smaller intervals (more precision/noise). Users with a long-term perspective may benefit from larger intervals (less precision/noise).    

Trading Interpretation

Momentum Bars interpretation is similar to that of traditional bar charts.

Strategy Back-testing & Automation

Strategies can be effectively back-tested and automated on Momentum Bar charts when using an appropriate Range value and a '1 Tick' underlying interval. Automating strategies on this chart type using higher underlying intervals will yield real-time results that are inconsistent with back-test results. For additional information on back-testing and automating strategies on Advanced Chart Types, see Advanced Chart Types - Strategy Back-Testing & Automation.

Additional Information

For a comprehensive list of command line commands, see Command Line References (All Commands) or Command Line Reference (Sorted by Application).

Related Topics

About the Chart Analysis Window